AIRGUN ADAPTERS

Features: 6061 Aluminum 1/2 x 20 male threads Black Anodized Thread Protector compatible up to 30 caliber

Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .177, .22 and .25 calibers

Please Read*  To pick the correct adapter, you will need to measure the length of your carbon fiber shroud. If your shroud measures 13 or 17 inches, you'll need A57. If your shroud measures 11.5 inches and you eventually want to use a longer bottle(580 cc) you'll need A72 If  your shroud is 11.5 inches long and you have no intentions of adding a longer bottle then go with A73 Easy to install 1/2 x 20 adapter for the LCS SK19. Convert your shroud to accept any 1/2 x 20 suppressor of your choice. I would highly recommend a Ronin one size up from what the gun's caliber is. Still very effective but more importantly reduces the chance of pellet clipping, especially during rapid fire. *Make sure to use a suppressor one caliber size up. Works really well and reduces the chance of pellet clipping. CNC Matte Black Anodize Compatible up to .30 caliber

Right handed threads to convert barrels with M14x1 to 1/2 x 20. Features: 16.05mm OD, 15.20mm deep on female side Black anodized and knurled throughout on the outside.

This adapter is about 22mm OD x 38.30mm Length. It converts barrel threads from M14x1.25 to 1/2 x 20.  Does not come with a thread protector.  Features: 6061 T6 Aluminum Silver (no anodize)

This adapter will allow you to screw on a 1/2 x 20 airgun suppressor. Features: Knurled cap CNC Matte black anodize *Make sure to use a suppressor one caliber size up. Works really well and reduces the chance of pellet clipping.

Nice addition to quiet down a nice entry level PCP bullpup, add any 1/2x20 suppressor of your choice.  *Make sure to use a suppressor one caliber size up. Works really well and reduces the chance of pellet clipping. Features: Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodized diamond pattern knurling thread protector Compatible with .22 and .25 calibers New model allows you to screw on larger diameter suppressors like the Sumo and Ronin without interfering with the fill probe

These adapters are for the RAW HM 1000x shrouds that are 2inches in diameter. Not compatible with the offset ones.  There are two types of shrouds out there, remove the factory short screw on suppressor.  If your shroud looks like the one in the picture below, select A65   If it looks like the shroud below then select A90. Does not have a thread protector. 

Please note* remove the front cap on your shroud. Measure the outer diameter of the threaded part. If close to 27mm, select this adapter. If not most likely A59 Features: Made of 6061 T6 Aluminum Matte black anodize Compatible up to 50 caliber Includes diamond knurled thread protector

If your Priest shroud sits behind the air bottle and you would like to use a larger suppressor, this extender will allow you to do so. Features: 6061 T6 aluminum Knurled cap Matte black anodize 

Sam Yangs are known to output some crazy power. This adapter with M18x1 threads will allow you to screw on the Emperor v3. You might have need the Extender as well if Silence is a Priority!

Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible up to .357 to .457 cal Seneca .357 uses 5/8x18 Please note* Sam Yang has two different types of barrel threads, M16x1.5 and 5/8x18. Best way to determine which threads you have is to go to a hardware store and pickup one of the bolts. If the bolt does not screw on then it must be the other size. If your barrel is too close to the fill probe you will need to get the extended adapter version. I currently do not have the short version of the 5/8x18.  

Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip

Note: You have to remove the factory threads first. The factory thread has two flat sides where they can use a wrench to turn it counter clockwise to remove. Then add on my adapter. Features: Compatible with .177 and .22 6061 Aluminum T6 1/2 x 20 male threads

Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Diamond pattern knurling for easy grip

Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .22, .25 and .30 calibers

This adapter will screw into the Mutant OEM shroud. Has 1/2 x 20 UNF male threads that allows you to screw on any 1/2 x 20 female threaded LDCs. Features: Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Cap with diamond pattern knurling for easy grip

This adapter will screw into the Mutant OEM shroud. Has 1/2 x 20 UNF male threads that allows you to screw on any 1/2 x 20 female threaded LDCs. Features: Made by CNC for accuracy Material is 6061 T6 Aluminum Black anodize Cap with diamond pattern knurling for easy grip

This adapter screws into the OEM shroud. Replaces the original front cap. Features: Comes with knurled cap CNC Matte black anodize Other things to consider: Gauntlet Aluminum Air Stripper **NOT COMPATIBLE WITH THE .30 CAL GAUNTLET 2

This adapter replaces the factory shroud baffle and has M18x1 threads. Comes with thread protector Instructions: remove the factory shroud by grabbing onto the shroud by the front cap. When you turn the shroud counter clockwise, that should loosen the front cap. The shroud is free floating, there are no threads in it. Important thing is to remove the front cap. once shroud is off, put a few drops of red loctite onto the barrel thread. put the shroud back on now take new shroud adapter and tighten onto barrel. Let it dry for a few minutes remove thread protector on shroud adapter to screw on an airgun suppressor with M18x1 threads.