Diana Outlaw 1/2 x 20 Adapter A44
$45.00
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Matte black anodize
Diamond pattern knurling for easy grip
Compatible with .177, .22 and .25 calibers
Remove factory suppressor and screw this into the shroud directly onto the barrel.
Dynamic Air Rifle (DAR) 1/2 x 20 Adapter A82
$40.00
Features:
Material is 6061 T6 Aluminum
Black anodize
Comes with knurled thread protector
Edgun Matador R3M 1/2 x 20 Adapter STD/Compact/Long A6
$100.00
The Edgun Matador R3M is one of the most accurate bullpups on the market. Like any gun, the shroud could be improved. This baffle unit replaces the OEM baffles. Unscrew the factory unit and screw on this one the same way. It was important to keep the rear bolt to help tension the barrel. I've added more vent holes in the rear to allow more air to flow to the rear of the shroud. At the tip of the unit there is now a built in 1/2 x 20 adapter with a knurled thread protector.
Features:
Made of steel for durability
Compatible with .22 and .25
fits Standard, Compact and Long Matadors
CNC machined
Comes with Knurled cap
Includes O-ring
Evanix Rainstorm 1/2 x 20 Adapter A29
$50.00
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Matte black anodize
Diamond pattern knurling for easy grip
Compatible with .22 to .30 cal.
Evanix Rainstorm/Sniper, Winchester 70-35 M18x1 Adapter A28
$45.00
Note* for Winchester 70-35, if your gun did not come with a factory suppressor, use this adapter. If it did come with a factory suppressor we would have to make a custom adapter.
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Matte black anodize
Diamond pattern knurling for easy grip
Compatible with .357 and .45 model
FX Bobcat Shroud Extender With 1/2 x 20 Adapter A3
$40.00
This adapter will extend the shroud past the air tube allowing you to screw on any suppressor with 1/2 x 20 female threads. Female side is M20x1 and male 1/2 x 20.
Features:
Matte Black anodize
Knurled thread protector
95mm long
FX Crown 1/2 x 20 Adapter A22
$40.00
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Matte Black anodize
Knurled thread protector
Installation instructions
FX Impact/Wildcat 1/2 x 20 Adapter A2
$50.00
Note: If you need a shroud extender for your 600mm FX Impact to work with the Saber Tactical TRS rail, you'll need this adapter: A101
This adapter is for Impacts and Wildcats that have the M20x1 male threaded end. It will screw onto your factory shroud and allow you to screw on an LDC with a 1/2 x 20 UNF Female threads. Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Matte Black anodize
Knurled thread protecton
FX Shroud Extender 1/2 x 20 Female to 1/2 x 20 Male A101
$35.00
This adapter adds .75 inches to the FX shroud. Female 1/2 x 20 to Male 1/2 x 20
Features:
6061 T6 aluminum
length .75 inches
Includes thread protector
Black anodize
Weights: 1.5oz
28MM outer diameter
FX Shroud Extender 1/2 x 20 Female to 1/2 x 20 Male A102
$45.00
This adapter adds 2.5 inches to the FX shroud.
Features:
6061 T6 aluminum
length 2.5 inches
Includes thread protector
Black anodize
Weights: 3.7oz
28mm outer diameter
FX Wildcat / FX Royale 400/500 Adapter A12
$50.00
These adapters are for Wildcat shrouds that extend past the air tube and has female threads once you remove the front shroud cap. It is also compatible with FX Royale 400/500, Boss and Whisper. This adapter is Male to Male, one side is M20x1 that goes into the shroud and the other end is 1/2 x 20 UNF.
Features
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Diamond pattern knurling for easy grip
*Note if you have a newer Wildcat, this is not the correct adapter. You will need this one instead: https://donnyfl.com/collections/adapters/products/fx-impact-wildcat-1-2-x-20-unf-adapter-matte-finish-with-thread-protector
FX Wildcat Shroud Extension 1/2 x 20 Adapter A1
$50.00
This shroud extension is for shrouds that sits behind the lower air tube. Female side is M20x1 and male 1/2 x 20.
Features
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
44mm long
Gamo TC35, TC45/ Evanix Rex, Rex P M18x1 Adapter A59
$40.00
*Please note: Take the front cap off your shroud, measure the outer diameter of the threads on the cap. If close to 1.4 inches, use this adapter.
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Diamond pattern knurling for easy grip
Hatsan Blitz 1/2 x 20 Adapter A84
$40.00
This adapter allows you to screw on an airgun suppressor with 1/2 x 20 threads.
I recommend going with the Ronin 1/2 x 20 with this gun. I have it installed on my personal gun and it works flawlessly. However, results may vary and might need modification to work in semi auto mode. This gun is similar to the Bullmaster and others have been able to fix the issue by replacing the spring. Go to your hardware store and look for a lighter spring. I got mine from Ace hardware and it fixed the magazine indexing issue.
Features:
Compatible up to .30 caliber
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Diamond pattern knurling for easy grip
Hatsan Bullmaster/Galatian 1/2 x 20 Adapter A35
$40.00
1/2 x 20 UNF adapter for those rapid firing Bullmaster. New and improve design to allow more air flow.
Please note that when you add a suppressor to this gun, it does not properly index the magazine. It uses blowback air to advance the magazine however with a suppressor on, it over rotates and causes it to not properly index. If you plan to single load it'll work fine. Some customers have been able to get the gun to work properly by swapping out the spring inside the shroud with a different strength one. Will take trial an error.
Similar to the Blitz, this guy may need a lighter spring to work with a suppressor. I got mine from Ace hardware. See picture
Features:
Compatible up to .30 caliber
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Diamond pattern knurling for easy grip
Hatsan Jet 1 & Jet 2 Adapter A111
$40.00
Features:
Any gun that needs a double-sided male adapter
Has through holes in the threads for easy tightening or loosening
Matte Black Anodize threads
.655 inches / 16.6 mm OD***USE WITH A MODERATOR THAT IS ONE CALIBER HIGHER***
Hatsan Pile Driver Adapter
$45.00
Features:
Compatible with .45 and .50 caliber
Made of steel
M18x1 threads compatible with Emperor with M18x1 endcap
Comes with black anodized Aluminum thread protector
Adapters are tight fit and has four set screws (M4) to help secure it onto the barrel
Uses 2mm hex keys for set screws
NOTE: We've seen some variance in the OD of barrels recently, please include a note of your barrel's EXACT OD (for example .7790 inches-be precise because custom adapters are not returnable or refundable) so we can custom cut your adapter to fit.
Hatsan QE 1/2 x 20 Adapter A24
$45.00
If you have a Hatsan Bully .25/.30- based on customer's feedback, I would go with the Emperor.
*We have not had any success with customers using a suppressor on Hatsan's line up of semi auto guns. It causes the gun to not index properly.
Features:
Matte black Anodized
CNC
Includes knurled thread protector
Compatible up to .30
Compatible with the following guns:
Hatsan GladiusHatsan Flash Wood QEHatsan AirMaxHatsan Bullboss QEHatsan BT65 QEHatsan Nova QEHatsan AT44-10 QEHatsan Hercules QEHatsan Flashpup QEHatsan AT P1Hatsan Flash QE
Hatsan QE Big Bore .357/.457 M18x1 Adapter A54
$45.00
Features:
Matte black Anodized
CNC
Includes knurled thread protector
Compatible for the .357 and .457 model
The new Factor BP in .357 cal has M14x1.25 threads on the QE system, so for that air rifle you need a moderator with an M14x1.25 endcap, not an adapter.
Hatsan Riptor 1/2 x 20 Adapter A14
$40.00
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Grey anodize
Diamond pattern knurling for easy grip
Compatible with .22 and .25 calibers