
Airforce Texan LSS Adapter A65
$40.00
This adapter screws directly to the end of the factory Texan LSS shroud.
It has M18x1 male threads to pair with my big bore suppressors. Add an Emperor or Ronin to tame the beast!
Features:
6061 Aluminum
Matte black anodize
knurled thread protector

AirMak Caiman 1/2 x 20 Adap...
$45.00
Features:
Compatible with .177, .22 and .25
6061 Aluminum T6
Black anodized
Knurled cap
1/2 x 20 male threads

AirMax MKII/PP700 1/2 x 20 ...
$40.00
What's even better than a fun gun? A quiet one! Stainless steel adapter now allows you to put on more effective after market suppressors. There's a through hole in the threads to help tighten it onto the gun or assist to remove. I've seen some scratched up guns where people slipped with a prong trying to tighten or remove.
Features
Made by CNC for accuracy
Stainless Steel
Black anodized diamond pattern knurling thread protector

American Air Arms - EVOL 1/...
$40.00
This adapter screws into the OEM shroud allowing you to screw a suppressor with 1/2 x 20 UNF of your choice.
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Matte black anodize
Includes thread protector
Compatible up to .30 cal

American Air Arms- Slayer M...
$45.00
This adapter screws into the OEM shroud allowing you to screw on either the Emperor or .357 Ronin.
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Matte black anodize
Diamond pattern knurling for easy grip
M18x1 threads

Artemis PP750/ Snowpeak PP7...
$35.00
This adapter replaces the PP750 factory front cap. Has 1/2 x 20 threads to screw on an airgun suppressor.
Features:
6061 Aluminum
CNC machined
Matte black finished

Ataman AP16 Pistol 1/2 x 20...
$40.00
This beautiful pistol has a little bark to it. Add this adapter to it and your favorite suppressor to make it more enjoyable .
Features:
through hole in 1/2 x 20 threads for easy tightening or removal
hole on side of adapter in case adapter is stuck in suppressor
knurled cap
CNC
Matte black anodize

Ataman BP17
$40.00
There are two options for the BP17
Option 1: If you would like to keep the factory shroud and add a suppressor to the end of it get #A49
Option 2: If you would like to remove the factory shroud and keep the gun as short as possible with a suppressor, select #A74. This is the version Ted did a review on.

Ataman M2R .357 M18x1 Adapt...
$45.00
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Matte black anodize
Diamond pattern knurling for easy grip
Compatible with .357 model

Ataman M2R 1/2 x 20 Adapter...
$40.00
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Matte black anodize
Diamond pattern knurling for easy grip
Compatible with .22 and .25 calibers

Beeman Underlever 1357 | 13...
$45.00
This adapter replaces the factory baffle allowing you to screw on a 1/2 x 20 airgun suppressor. You will need to remove the factory o'ring and put it on the new adapter.
Features:
6061 aluminum T6
Black anodized
Knurled thread protector

Benjamin .357 Bulldog M18x1...
$45.00
This design goes back to the barrel and slides over the barrel bushing. This will keep the barrel aligned with the adapter's exit hole. Please note that the barrel bushing is not included. Factory gun already includes the bushing.
The .357 Benjamin Bulldog is becoming popular for big game hunting. Add this adapter and pair it up with a .357 Ronin or .357 Emperor to make it the ultimate hunting airgun.
I would recommend going with minimum the .357 Ronin for this gun. The .357 FX suppressor is not enough to quiet this gun down.
IF you use an Emperor with this gun, do not add the extender. Too much weight added applied to the adapter and may cause inaccuracies.
Made by CNC for accuracy
Very easy to install. Remove the top and bottom screw securing the front cap and swap it out for this adapter. Screw the two screws back in and you're done. No need to remove the shroud.
Matte Black anodize
Knurled thread protector
When putting this on, press the adapter into the shroud as you tighten the two screws. This will ensure the adapter is flush with the shroud.

Benjamin Akela/Kratos 1/2 x...
$40.00
*Note: For the Akela, remove one of the factory baffles in order for the adapter to fit flush.
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Matte black anodize
Diamond pattern knurling for easy grip
Compatible with .177, .22 and .25 calibers

Benjamin Discovery/Maximus ...
$40.00
Features:
This adapter has a 1/2 x 20 adapter at the end
Has two holes on top like OEM so you can use original screws and front site.
Overall length from one end to the other is 3.12 inches
has groove underneath just like OEM for ease of removing fill cap
CNC
Matte Black Anodize
Match this up with a .22 Tatsu and you have a nice quiet gun.

Benjamin Marauder Pistol (P...
$40.00
Want to make your Prod quieter? You'll need this 1/2 x 20 adapter, it will screw into the OEM shroud. The threads that screws into the shroud is 11/16 - 24.
The Sumo 1/2 x 20 is my favorite suppressor for this gun. However, in order to fill this gun with the Sumo, you'll have to remove the suppressor. An alternative is to go with either the Tanto or KOI with cone rear cap.
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Diamond pattern knurling for easy grip

Benjamin Marauder Pistol (P...
$45.00
This adapter extends the shroud 1.5 inches or about 38.1mm. Pair it up with a .22-25 Tanto 1/2 x 20 Bolt #S69 and this pistol will be very quiet. No need to remove the suppressor to fill the gun.
Features:
6061 Aluminum
Black anodized
Comes with knurled thread protector

Benjamin Marauder(Mrod)/For...
$40.00
Marauders are great entry level PCP guns. There are lots of mods you can do to make them more powerful. More power means a louder gun. To make it backyard friendly, make sure to grab this adapter to allow you to screw on an aftermarket LDC. Threaded end that goes into the OEM shroud is 13/16 - 28.
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Diamond pattern knurling for easy grip

Brocock Compatto 1/2 x 20 A...
$40.00
Want to make your Compatto quieter? You'll need this 1/2 x 20 adapter that will screw into the OEM shroud. The threads that screws into the shroud is 11/16 - 24.
Features:
Made by CNC for accuracy
Material is 6061 T6 Aluminum
Black anodize
Diamond pattern knurling for easy grip

Bushbuck .45 M18x1 Adapter A48
$45.00
This slide on adapter will fit the Bushbuck up to .45 cal. I would recommend the .45/50 Emperor v3 along with the 6.5 inch extender to tame this beast!