Products

Proudly wear DonnyFL's Limited edition Retro Style Hoodie with confidence! Our premium quality hoodie comes in a cotton/polyester mix. It's light weight, warm, and comfy wieghting in at 1.3 lbs. 

Proudly wear the DonnyFL Limited Edition Retro T-shirts with confidence! Our Next Level men's premium fitted short sleeve crew t-shirt comes in 100% cotton. It's light weight at 5.0 oz. fabric laundered for reduced shrinkage, super soft baby rib-knit set collar and a tear-away label. These were made to wear in any scenario, they are THAT comfortable! 

Features: Material is 6061 T6 Aluminum Black anodize Comes with knurled thread protector

This kit is to replace the stock factory shroud and allows you to screw on an airgun suppressor with 1/2 x 20 threads. The shroud is 2 inch in diameter so best to use Ronin/Emperor/Fatboy with it.  Things to keep in mind:  Mechanical noise will still be loud. Nothing we can do to reduce that with our kit. Have someone shoot the gun and take about 10 steps back. You'll get a better feel for the muzzle noise. The shroud is empty to provide the max air expansion. The stock will fold but will not lock. you will need to get the extended pin from Edgun West Available in two sizes 250mm and 350mm It's ok to use the 350mm shroud on a 250mm barrel (more volume = quieter) Features: Made of 6061 T6 Aluminum Black anodized 1/2 x 20 male threads (does not have a thread protector) Comes with 2 Stainless Steel screws  Instructions

The Edgun Matador R3M is one of the most accurate bullpups on the market. Like any gun, the shroud could be improved. This baffle unit replaces the OEM baffles.  Unscrew the factory unit and screw on this one the same way. It was important to keep the rear bolt to help tension the barrel. I've added more vent holes in the rear to allow more air to flow to the rear of the shroud. At the tip of the unit there is now a built in 1/2 x 20 adapter with a knurled thread protector.  Features: Made of steel for durability Compatible with .22 and .25 fits Standard, Compact and Long Matadors CNC machined Comes with Knurled cap Includes O-ring 

This tool makes degassing the Edgun R3M and R3 safe and easy. It also acan also be used to pull out the regulator. Instructions: before screwing the tool onto the Edgun, back out the screw a little to allow the valve pin to go into the tool.  screw the tool onto the valve Using the blue knob slowly screw into valve pin. You'll start to hear a hissing noise and that's the air being released.  once empty, your gauge should be down to zero to remove the regulator, make sure the gun is completely empty. Unscrew the screws holding the regulator in place. Once all the screws are out, screw the degasser tool onto the valve and pull it out of the air tube

Get ready to pounce on the ultimate style sensation with the El Gato Muerto Performance Hoodie with UPF 50 by Disco Donny! This limited-time offer is a game-changer that fuses fashion and functionality into one purr-fect package. Crafted with sublimated dry fit technology, this hoodie keeps you cool and comfortable in the most stylish way possible. The mesmerizing design, meticulously printed all over, will make you the envy of the party, the gym, or wherever your adventures take you. The sublimated print is a work of art, showcasing vibrant colors and intricate patterns that scream individuality. The El Gato Muerto Performance Hoodie by Disco Donny is a limited-time offer, so act fast and get your hands on this remarkable piece of wearable art before it's gone.

Is the 10.5 inch Emperor v3 still too loud for you? If so add this 6.25 inch expansion chamber to the rear of the Emperor to make it even quieter. This increases the air volume that gets captured inside the suppressor. Works with the latest version of the Ronin as well. If it has the grooves in the front cap, it's the latest model.

Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .22 to .30 cal.

Note* for Winchester 70-35, if your gun did not come with a factory suppressor, use this adapter. If it did come with a factory suppressor we would have to make a custom adapter. Features:  Made by CNC for accuracy Material is 6061 T6 Aluminum Matte black anodize Diamond pattern knurling for easy grip Compatible with .357 and .45 model

This extended quick disconnect (QD) makes it easy for those guns with hard to reach fill nipples. A must have for FX Impacts. 1/8 BSP male threads Max 5000 psi (Do not exceed recommended pressure) Release collar close to 1.20 inches long Comes with sealed washer  

Need to make the fat boy quieter? You can add this 3 inch extender to capture more air and reduce the muzzle blast some more.  Features: 6061 T6 Aluminum Black anodize Matching outer tube design to the fat boy Also compatible with the Ronin and Emperor

This muzzle brake or air stripper screws onto the front of the fat boy.  Note: This unit does not come with the individual air strippers. You can change the caliber size by using the inserts that was included with the fat boy. Features: Made of aluminum 6061 T6 Black anodize Weights 2.9 oz Add the optional 3 inch extender for the fatboy to make it quieter!Extender

4.3 oz, 100% preshrunk soft jersey cotton Tear-away, removable labels Made to fit comfortably all day long available up to 3XL 

Black/Red with Black/White rubber patch logo. Fabric: 100% cotton front panels and bill, 100% polyester mid and back panels. Structure: Structured Profile: High Closure: 7-position adjustable snap

Very limited quantity special offer for the Fx Airguns 20mm diameter tensioning shroud. **NOT ANODIZED**  

Suppose you have extra FX barrels laying around and you want to use them with your Leshiy 2. This adapter will allow you to attach an FX Airguns native barrel to your rifle.  Remove the FX factory brass transfer port and screw on our adapter. Slide the barrel back in and you're all set to go. Currently only available for the .22 and .25 & .30 caliber barrels.

This adapter will extend the shroud past the air tube allowing you to screw on any suppressor with 1/2 x 20 female threads. Female side is M20x1 and male 1/2 x 20. Features: Matte Black anodize Knurled thread protector 95mm long

Features: Made by CNC for accuracy Material is 6061 T6 Aluminum Matte Black anodize Knurled thread protector Installation instructions

Note: If you need a shroud extender for your 600mm FX Impact to work with the Saber Tactical TRS rail, you'll need this adapter: A101 This adapter is for Impacts and Wildcats that have the M20x1 male threaded end. It will screw onto your factory shroud and allow you to screw on an LDC with a 1/2 x 20 UNF Female threads. Features: Made by CNC for accuracy Material is 6061 T6 Aluminum Matte Black anodize Knurled thread protecton